Product
- Industrial
- Conductivity Meter
- Resistivity Meter
- pH Meter
- Reverse Osmosis Controller
- Flow Meter
- Dissolved Oxygen Meter
- Free chlorine analyzer
- Turbidity Meter
- TSS Meter
- COD
- Fluorion Analyzer
- Sodium Meter
- Silicate Meter
- Hydrazine Analyzer
- Multiparameter analyzer
- Management system
- Transmitter
- Sensor
- Control Panel
- Installation Accessories
- Plastic Electric Box
- water treatment materials
- One-stop Purchase Materials
- Handheld
- Portable Conductivity Meter
- Portable pH meter
- Portable pH and conductivity a
- Portable pH and conductivity m
- Portable pH and dissolved oxyg
- Portable pH ORP conductivity D
- Portable ORP meter
- Portable Dissolved Oxygen mete
- Portable conductivity and DO m
- Portable Free Chlorine meter
- Portable Acid Meter SX7120
- Portable Acid-Alkali Meter SX7
- Portable Hardness Meter YD300
- Portable turbidity meter
- Portable Thermometer
- Portable Tachometer -laser typ
- Portable aquaculture multipara
- Portable COD
- Pentype Conductivity Meter
- Pentype TDS Meter
- Pentype pH meter
- Pentype ORP meter
- Pen type conductivity TDS sali
- Pentype Free Chlorine Meter
- Dual channels TDS Meter for Dr
- Handheld Refractometer
- Laboratory
- Laboratory Conductivity meter
- Laboratory Conductivity Meter
- Laboratory Conductivity and DO
- Laboratory pH meter
- Laboratory pH meter -precise M
- Laboratory pH and Conductivity
- Laboratory pH and Conductivity
- Laboratory pH and DO meter MP5
- Laboratory Dissolved Oxygen me
- Laboratory Turbidity Meter
- Laboratory Fluoride Ion Meter
- Laboratory Sodium Meter
- Laboratory BOD analyzer (diffe
- Laboratory COD Ammonia Nitroge
- Laboratory Calcium Ion Meter M
- Laboratory chroma meter CLR-3
- Laboratory Electrode
- Stirrer
- Accessories
- Aquarium
PC-8750
AddTime：2016-12-02 13:56:13 Views: 0
1. Installation
1.1 Installation of the instrument panel. 1. This instrument needs a hole of 92 x 92mm. 2. Press the back of the instrument with the mounting bracket until the quick-fixed card lock the grooves on the two sides of the instrument. 3. When removing the instrument, it is necessary to fix the instrument temporarily with adhesive tapes or hold the back of the instrument firmly in order to prevent the instrument from falling down. Pull the quick-fixed cards outwardly and draw out the instrument. |
 |
 |
| General introduction Compatible sensor: Standard type pH/ORP detector (BNC) The housing box for packing n Protection grade: IP65, front n Material of the shell: ABS n Screen: synthetic polyester n Keys: 4 encapsulated silicone keys n Weight: about 225g Display: n LCD display with backlight, LCD 2x16 bit n Contrast: defined by users, 5 levels n Refresh rate: 3s Electrical performance n Power: 24V DC Input range of the sensor n pH: 0.00～14.00pH n ORP: -2000Mv～+2000mV n Temperature: PT1000, -25-125℃ Current Output Signal n Optically isolated 4-20mA, reversible, can migrate n Maximum impedance of the loop: 600Ω max.@ 24V |
n Refresh rate: 3S n Accuracy: ±0.03mA@25℃,24V Control output signals n Operating mode: Hi/Lo/off (normally open contact) n Capacity of the relay contact: 2A/250V AC (resistive load) 2A/28V DC (resistive load) Pulse Output Signal n Output signal of the open collector, optical isolation n The maximum pull-down current is 50mA and the maximum pull-up voltage is 30VDC. n Pulse modes (maximum pulse rate: 400p/m) 485 communication output signal [Do not have this function] Specifications and dimension n Overall dimension: 96x96x46mm (height x width x depth) n The dimension of the hole: 92x92mm (height x width) Environmental conditions n Working temperature: -10~70℃ n Storage temperature: -15~80℃ n Relative humidity: 0~95%, no dew point n Insulation grade: II |
